Willkommen zurück
Melden Sie sich bei Ihrem Altimeter Cloud Konto an
Noch kein Konto? Registrieren
Kostenloses Konto erstellen
Wir senden Ihnen einen Bestätigungslink per E-Mail. Prüfen Sie auch Ihren Spam-Ordner.
Haben Sie bereits ein Konto? Anmelden
Startseite
Gerät: 1000-3BF4-4B04
Flug-ID: 1678Mini Hustler flight 24
Flugzusammenfassung
Höhe
Apogäum
120.98 Meter
Zeit bis Apogäum
5.92 seconds
Brennschluss-Höhe
52.1 m
Max. Geschw.-Höhe
50.56 m
Auswurf-Höhe
120.8 m
Lande-Höhe
-0.99 m
Stabilität
Stabilitätswert
94.9 / 100 (Ausgezeichnet)
Neigung bei Brennschluss (20%)95.5
Nick/Gier-Rate (30%)96.8
Coning · boost (25%)95.1
Schubgeradheit (15%)92.7
Launch tilt 1.7° · Coning 18/22.5°/s · Spin 86.9°/s · Thrust 98.6%
About this score
Worked out from the flight log between liftoff and 80% of apogee, independent of the angle the altimeter was mounted at in the airframe.
Neigung bei Brennschluss (20%) – how close to vertical it left the rod.
Nick/Gier-Rate (30%) and Coning · boost (25%) – how much the nose swung off the rocket's own axis. The main factor.
Schubgeradheit (15%) – how cleanly the motor pushed along the body.
Spin about the rocket's own axis is not counted against it — a fast, straight spin is stable. The line under the bars shows the raw measurements.
Geschwindigkeit
Max. Aufstieg
38.91 m/s
Max. Abstieg
-13.95 m/s
Bei Brennschluss
38.040 m/s
Landegeschw.
-7.255 m/s
Abstiegsgeschw.
-7.141 m/s
Auswurfgeschw.
1.75 m/s
Recovery
Single deploy (no dual deploy detected)
Beschleunigung
Max. Aufstieg
26.66 G
Max. Abstieg
13.26 G
Max. während Brennen
8.51 G
Durchschn. Aufstieg
0.04 G
Durchschn. Brennen
1.48 G
Zeiten
Brennschluss (erster)
2.02 seconds
Apogäum
5.92 seconds
Möglicher Auswurf
5.796 seconds
i
This ejection time was detected by the website from the accelerometer data, because the firmware did not record one for this flight.
Landung
22.82 seconds
Winkel
Rampen-Neigung
23.82°
Thrust calc pad tilt
1.7°
Max. Neigung bis Brennschluss
28.19°
Start-Roll
18.20°
Start-Nick
15.62°
Max. Drehung (Brennen)
153.82 dps
Durchschn. Drehung (Brennen)
85.3 dps
Allgemein
Upload-Datum
02/06/26-22:50:40
Datenpunkte
2704
Gesamte Aufnahmezeit
31.378 s
Durchschn. Abtastrate/s
86.1
Anzahl Sperren
0
Aufnahme-Höhe
-15.45 m
Start nach Einschalten
4m 51s
Referenzachse
X
Batterie & Temperatur
Batterie Start
100%
Batterie Ende
100%
Temperatur Start
33.09°C
Temperatur Ende
33.63°C
Flugdaten-Animation
FLIGHT 1678
120.98 Meters
ALTITUDE
0.00m
VELOCITY
0.00m/s
ACCEL
0.00G
TILT
0.00°
PITCH
0.00°
ROLL
0.00°
YAW
0.00°
TIME
0.00s
AWAITING LAUNCH
ALT
altimetercloud.com
LAUNCH
T+0.00s
LANDING
BURNOUT
Motor burn complete
Hinweis: Die Fluganimation erfordert eine feste Ausrichtung Ihres Höhenmessers. Kalibrieren Sie Ihre Sensoren für beste Ergebnisse.
Benutzernotizen
Mini Hustler flight 24. Carrying four other altimeters, but due to user error only got data from two of them.
Fügen Sie dieses Gerät Ihrem Konto hinzu, um zu bearbeiten
Youtube-Video
Kein Video
Fügen Sie dieses Gerät Ihrem Konto hinzu, um zu bearbeiten
Flugbilder (0)
Keine Bilder
Verknüpfte Rakete
Keine Rakete mit diesem Flug verknüpft
Geräteinformationen
Nano V1
Dieser Flug wurde mit einem geflogen: Nano V1.
Hardwareversion
Rev 4
Softwareversion
1.51
Zuletzt online
02/06/26-22:50:40
Drucksensor
Bosch BMP 581
Beschleunigungssensor
32G 3-axis
Gyroskop
2000 dgps 3-axis
Flugmotoren
1st Stage
1x
Estes
C6-5
Brenndauer
1.86 seconds
Diameter
18.00 mm
Durchschn. Schub
4.74 N
Max. Schub
14.09 N
Impuls
8.82 Ns
Impulsklasse
C
Gesamtgewicht
24.10 g
Treibstoffgewicht
10.80 g
Treibstofftyp
black powder
Links
Fügen Sie dieses Gerät Ihrem Konto hinzu, um zu bearbeiten
Motorbrenndauer
The dashed line is the combined thrust curve for your motors (data from thrustcurve.org), scaled so its peak matches the recorded acceleration maximum — the shape is meaningful, the absolute level is not (your rocket's weight is unknown).
Startplatz, Datum & Uhrzeit
Klicken Sie auf die Karte, um Ihren Startplatz zu markieren. Wechseln Sie zwischen Karten- und Satellitenansicht.
No results found — try a different search.
Klicken Sie auf die Karte · Ziehen zum Anpassen
Lat—
Lng—
✓ Launch location saved successfully.
✗ Could not save location — please try again.
Flugvergleich
Comparing against 3 other flights with the same motor configuration.
Highest apogee120.98 m 4th of 4
The maximum altitude reached above the launch point.
you
best
best 125.7 m · Mini Hustler flight 25 (#1679)
Best stability94.9 /100 1st of 4
How straight it flew: launch, coning and thrust straightness combined. 100 is perfect.
you
best
best 94.9 /100 · you
Fastest velocity38.91 m/s 3rd of 4
Peak ascent velocity recorded during the flight.
you
best
best 41.64 m/s · Mini Hustler flight 30 (#1695)
Best avg burn G1.1 G 1st of 4
Average acceleration during the motor burn, in G.
you
best
best 1.1 G · you
Longest flight31.37 s 4th of 4
Total recording time from launch to landing.
you
best
best 40.15 s · Mini Hustler flight 25 (#1679)
Lowest spin85.3 dps 2nd of 4
Average spin rate during the burn.
you
best
best 74.23 dps · Mini Hustler flight 30 (#1695)
Coldest flight0.33 C 2nd of 4
Board temperature at launch.
you
best
best 0.21 C · Mini Hustler flight 30 (#1695)
🌲 Is it in a tree?-0.99 m 1st of 4
Just for fun: whichever flight came down closest to 8 m above the launch point (roughly tree height) is the one most likely stuck up a tree.
8 m
you
best
closest to 8 m · you at -0.99 m
Allgemeine Flugeinstellungen
Dies ist ein Schnappschuss der für diesen Flug verwendeten Einstellungen. Gehen Sie zur
Gehen Sie zur Meine Geräte Seite und konfigurieren Sie die Einstellungen..
Prognosedruck
i
Set this to your local forecast pressure at sea level. This will offer you slightly improved accuracty for your flight, although it's not 100% essential every little helps!
Xcweather.co.uk is a decent place to grab pressures from for your location and time.
Xcweather.co.uk is a decent place to grab pressures from for your location and time.
1013.2 mbar
Starterkennung
i
This is the altitude above the launch pad altitude where the altimeter will trigger itself into recording / flight mode.
The altimeter keeps a constant average of the pressure while waiting for launch, it uses a simple algorithm and the pre-flight buffers to do this. The most recent 120 samples (~4 seconds) are ignored so your pre-trigger altitude won't effect the ground baseline.
For almost all uses we suggest keeping this on the 25 Meter (~82 feet) default settings. If you want to test your altimeter by throwing it in the air, or are planning a very low flight you may want to lower the setting.
The altimeter keeps a constant average of the pressure while waiting for launch, it uses a simple algorithm and the pre-flight buffers to do this. The most recent 120 samples (~4 seconds) are ignored so your pre-trigger altitude won't effect the ground baseline.
For almost all uses we suggest keeping this on the 25 Meter (~82 feet) default settings. If you want to test your altimeter by throwing it in the air, or are planning a very low flight you may want to lower the setting.
30 meters
Abtastverhältnis
i
The altimeter runs at 50Hz however you can record every sample or every X samples in order to extend the log time. For example if you set the ratio to 1 it will save 1:1 samples, or if you set it to 3 it will save 1 in 3 samples.
1:1 (50Hz)
Max. Abtastungen
i
This is the maximum samples the altimeter will log per flight. When it reaches this amount it will stop and save the recording.
24000
Aufnahme-Stopp
i
This setting is how the altimeter decides to stop recording. You can choose either 450 (~9s) or 900 (~18s) samples stable or it will record until the max samples limit unless you press the BUTTON in Manual stop mode.
The samples stable method waits for the devices altitude not to change for the set number of samples. This is defined by not changing by more than +/- 1.0 meters for 98% of the samples, it's a reliable method to stop the recording after landing within 8-10 seconds (300 sample) or 16-20 seconds (600 sample).
The samples stable method waits for the devices altitude not to change for the set number of samples. This is defined by not changing by more than +/- 1.0 meters for 98% of the samples, it's a reliable method to stop the recording after landing within 8-10 seconds (300 sample) or 16-20 seconds (600 sample).
Auto: 450 samples stable (~9s)
Oversampling
i
Oversampling is a internal setting of the BMP 390 pressure sensor. It is how many samples are taken for each reading. By taking multiple samples for each pressure reading the altimeter reduces noise and increases the resolution of the output.
The sensor can run at 50 samples per second in 4X mode, so we suggest leaving it in this mode as it will offer the highest accuracy.
The sensor can run at 50 samples per second in 4X mode, so we suggest leaving it in this mode as it will offer the highest accuracy.
16x Oversampling
IIR-Filter
i
The IIR filter is another internal sensor for the BMP390 pressure sensor. It is a Infinite impulse response filter used to enhance pressure measurement accuracy by reducing noise. It's primarily for smoothing out rapid pressure changes.
We suggest not setting this too high as it will cause delay to changes in altitude if set very high.
We suggest not setting this too high as it will cause delay to changes in altitude if set very high.
COEFF 7
Druckfilter
i
This filter is a software Kalman filter that runs on the altimeters processor.
The Kalman filter uses a prediction step based on a system model and then a correction step using new measurements to refine its estimate, it creates accurate most certain results from data with noise in it.
The Kalman filter uses a prediction step based on a system model and then a correction step using new measurements to refine its estimate, it creates accurate most certain results from data with noise in it.
TruePath 1.0
Sample speed
i
The sample rate of the altimeter's sensors. 50Hz takes 50 samples per second, 100Hz takes 100 samples per second for higher resolution data.
100 Hz
Hybrid mode
i
When enabled, the altimeter records at full speed during ascent then switches to half speed after apogee to extend recording time during descent.
Enabled (1/3 rate after apogee)
Sensorsynchronisation
i
The filters on the pressure sensor can cause it to lag very slightly behind the Accelerometer and Gyroscope data.
The Sync sensors option detects how far out of sync these sensors are. It then corrects the Acceleration and Gyroscope readings to match the pressure sensor.
AKTIVIERT
Ausrichtung
i
This is the orientation you intend to install the Altimeter in your rocket. It's needed to ensure completly accurate angles and orientation charts and reports. Check out the Manual for more information on this.
Down (text up)
IMU-Filter
i
The IMU filter, or fusion filter takes the data from each axis of the Gyroscope and Accelerometer to calculate the Pitch, Roll, Yaw and tilt angle from vertical.
These filters can build up some discrepency over time so it's important to calibrate your sensors to minimise this.
Madgwick 6-Axis
Start-ALP
i
This is prevention against accidental launch detection.
With this disabled the launch is based only on pressure and something that creates a low pressure can trigger the flight by accident. For example pulling your nose cone off can even trigger it.
With this enabled the rocket also needs to have seen 8 samples (0.25 seconds) of acceleration above this setting in the last 3 seconds as well as the pressure drop to trigger. There is a backup trigger of 1.05 seconds of altitude being above the launch detect setting too.
There are very few situations where this option would cause issues, so we suggest leaving it on.
With this disabled the launch is based only on pressure and something that creates a low pressure can trigger the flight by accident. For example pulling your nose cone off can even trigger it.
With this enabled the rocket also needs to have seen 8 samples (0.25 seconds) of acceleration above this setting in the last 3 seconds as well as the pressure drop to trigger. There is a backup trigger of 1.05 seconds of altitude being above the launch detect setting too.
There are very few situations where this option would cause issues, so we suggest leaving it on.
1.5G
Startsperre
i
When enabled, the altimeter locks out recording for a set period after power on to prevent false triggering during setup.
DISABLED
Statische Temperatur
i
A fixed temperature value used for altitude calculation when the external temperature sensor is disabled or not connected.
15 °C
Sensorkalibrierung
Kalibrierungsversätze für diesen Flug.
Gyroskop
⚠ Gyroskop wurde nicht kalibriert
X
0.000°
Y
0.000°
Z
0.000°
Beschleunigungssensor
⚠ Beschleunigungssensor wurde nicht kalibriert
X
0.000 mG
Y
0.000 mG
Z
0.000 mG
Kommentare
Kommentare
Anmelden um zu kommentieren.
Anmelden um zu kommentieren.