Vítejte zpět
Přihlaste se ke svému účtu Altimeter Cloud
Nemáte účet? Vytvořit účet
Vytvořit bezplatný účet
Pošleme vám potvrzovací odkaz e-mailem. Zkontrolujte složku se spamem, pokud ho neobdržíte.
Již máte účet? Přihlásit se
Úvod
Zařízení: 1000-3BF4-4B04
Let ID: 1679Mini Hustler flight 25
Zobrazit události
Stáhnout
Upravit tepl. & tlak ?
Obrázek
Datové sady
Klikněte na legendu pro zobrazení nebo skrytí dat
Přiblížení
Klikněte a táhněte nebo použijte gesto
Porovnat let ?
Shrnutí letu
Výška
Apogeum
125.7 Metry
Čas do apogea
6.18 seconds
Výška vyhoření
60.81 m
Výška max. rychlosti
51.1 m
Výška vypuštění
125.7 m
Výška přistání
-0.99 m
Stabilita
Skóre stability
93.8 / 100 (Výborný)
Náklon při dohoření (20%)95.9
Klápění/zatáčení (30%)97.2
Coning · boost (25%)96.3
Přímost tahu (15%)87.7
Launch tilt 1.6° · Coning 16.9/19.5°/s · Spin 95.4°/s · Thrust 97.4%
About this score
Worked out from the flight log between liftoff and 80% of apogee, independent of the angle the altimeter was mounted at in the airframe.
Náklon při dohoření (20%) – how close to vertical it left the rod.
Klápění/zatáčení (30%) and Coning · boost (25%) – how much the nose swung off the rocket's own axis. The main factor.
Přímost tahu (15%) – how cleanly the motor pushed along the body.
Spin about the rocket's own axis is not counted against it — a fast, straight spin is stable. The line under the bars shows the raw measurements.
Rychlost
Max. stoupání
39.28 m/s
Max. klesání
-10.87 m/s
Při vyhoření
37.600 m/s
Rychl. přistání
-4.897 m/s
Rychl. klesání
-4.934 m/s
Rychl. vypuštění
2.12 m/s
Recovery
Single deploy (no dual deploy detected)
Zrychlení
Max. stoupání
24.61 G
Max. klesání
25.16 G
Max. při spalování
9.57 G
Prúm. stoupání
0.2 G
Prúm. spalování
1.97 G
Časy
Vyhoření (první)
2.19 seconds
Apogeum
6.18 seconds
Možné vypuštění
6.183 seconds
i
This ejection time was detected by the website from the accelerometer data, because the firmware did not record one for this flight.
Přistání
31.51 seconds
Úhly
Náklon rampy
26.73°
Thrust calc pad tilt
1.6°
Max. náklon do vyhoření
47.82°
Klápění při startu
-5.60°
Klopní při startu
26.16°
Max. rotace (spal.)
328.73 dps
Prúm. rotace (spal.)
102.37 dps
Obecné
Datum nahrání
02/06/26-22:51:54
Datové vzorky
3104
Celkový čas záznamu
40.154 s
Prúm. vzorký/s
77.3
Počet blokování
0
Výška záznamu
-11.42 m
Start po zapnutí
5m 37s
Referenční osa
X
Baterie & teplota
Baterie začátek
72%
Baterie konec
70%
Teplota začátek
34.22°C
Teplota konec
34.88°C
Animace dat letu
FLIGHT 1679
125.7 Meters
ALTITUDE
0.00m
VELOCITY
0.00m/s
ACCEL
0.00G
TILT
0.00°
PITCH
0.00°
ROLL
0.00°
YAW
0.00°
TIME
0.00s
AWAITING LAUNCH
ALT
altimetercloud.com
LAUNCH
T+0.00s
LANDING
BURNOUT
Motor burn complete
Poznámka: Animace letu vyžaduje montáž výškoměru v pevné orientaci. Kalibrujte senzory pro nejlepší výsledky.
Uživatelské poznámky
Mini Hustler flight 25. Four other altimeters aboard. Nominal flight.
Přidejte toto zařízení ke svému účtu pro úpravy
Youtube video
Žádné video
Přidejte toto zařízení ke svému účtu pro úpravy
Obrázky letu (0)
Žádné obrázky
Propojená raketa
K tomuto letu není připojena žádná raketa
Informace o zařízení
Nano V1
Tento let byl proveden na Nano V1.
Verze hardware
Rev 4
Verze software
1.51
Naposledy online
02/06/26-22:51:54
Snímač tlaku
Bosch BMP 581
Akcelerometr
32G 3-axis
Gyroskop
2000 dgps 3-axis
Motory letu
1st Stage
1x
Estes
C6-5
Burn time
1.86 seconds
Diameter
18.00 mm
Average thrust
4.74 N
Max thrust
14.09 N
Impulse
8.82 Ns
Impulse class
C
Total weight
24.10 g
Propellant weight
10.80 g
Propellant type
black powder
Links
Přidejte toto zařízení ke svému účtu pro úpravy
Spalování motoru
The dashed line is the combined thrust curve for your motors (data from thrustcurve.org), scaled so its peak matches the recorded acceleration maximum — the shape is meaningful, the absolute level is not (your rocket's weight is unknown).
Místo startu, datum a čas
Klikněte na mapu pro označení místa startu. Přepínejte mezi mapou a satelitním pohledem.
No results found — try a different search.
Klikněte na mapu · Přetáhněte pro úpravu
Lat—
Lng—
✓ Launch location saved successfully.
✗ Could not save location — please try again.
Porovnání letú
Comparing against 3 other flights with the same motor configuration.
Highest apogee125.7 m 1st of 4
The maximum altitude reached above the launch point.
you
best
best 125.7 m · you
Best stability93.8 /100 2nd of 4
How straight it flew: launch, coning and thrust straightness combined. 100 is perfect.
you
best
best 94.9 /100 · Mini Hustler flight 24 (#1678)
Fastest velocity39.28 m/s 2nd of 4
Peak ascent velocity recorded during the flight.
you
best
best 41.64 m/s · Mini Hustler flight 30 (#1695)
Best avg burn G1.06 G 2nd of 4
Average acceleration during the motor burn, in G.
you
best
best 1.1 G · Mini Hustler flight 24 (#1678)
Longest flight40.15 s 1st of 4
Total recording time from launch to landing.
you
best
best 40.15 s · you
Lowest spin102.37 dps 3rd of 4
Average spin rate during the burn.
you
best
best 74.23 dps · Mini Hustler flight 30 (#1695)
Coldest flight0.34 C 4th of 4
Board temperature at launch.
you
best
best 0.21 C · Mini Hustler flight 30 (#1695)
🌲 Is it in a tree?-0.99 m 2nd of 4
Just for fun: whichever flight came down closest to 8 m above the launch point (roughly tree height) is the one most likely stuck up a tree.
8 m
you
best
closest to 8 m · Mini Hustler flight 24 (#1678) at -0.99 m
Obecná nastavení letu
Toto je snímek nastavení použitých pro tento let. Přejděte na
Přejděte na stránku Moje zařízení a nakonfigurujte nastavení..
Předpovězený tlak
i
Set this to your local forecast pressure at sea level. This will offer you slightly improved accuracty for your flight, although it's not 100% essential every little helps!
Xcweather.co.uk is a decent place to grab pressures from for your location and time.
Xcweather.co.uk is a decent place to grab pressures from for your location and time.
1013.2 mbar
Detekce startu
i
This is the altitude above the launch pad altitude where the altimeter will trigger itself into recording / flight mode.
The altimeter keeps a constant average of the pressure while waiting for launch, it uses a simple algorithm and the pre-flight buffers to do this. The most recent 120 samples (~4 seconds) are ignored so your pre-trigger altitude won't effect the ground baseline.
For almost all uses we suggest keeping this on the 25 Meter (~82 feet) default settings. If you want to test your altimeter by throwing it in the air, or are planning a very low flight you may want to lower the setting.
The altimeter keeps a constant average of the pressure while waiting for launch, it uses a simple algorithm and the pre-flight buffers to do this. The most recent 120 samples (~4 seconds) are ignored so your pre-trigger altitude won't effect the ground baseline.
For almost all uses we suggest keeping this on the 25 Meter (~82 feet) default settings. If you want to test your altimeter by throwing it in the air, or are planning a very low flight you may want to lower the setting.
30 meters
Sample ratio
i
The altimeter runs at 50Hz however you can record every sample or every X samples in order to extend the log time. For example if you set the ratio to 1 it will save 1:1 samples, or if you set it to 3 it will save 1 in 3 samples.
1:1 (50Hz)
Max samples
i
This is the maximum samples the altimeter will log per flight. When it reaches this amount it will stop and save the recording.
24000
Recording stop
i
This setting is how the altimeter decides to stop recording. You can choose either 450 (~9s) or 900 (~18s) samples stable or it will record until the max samples limit unless you press the BUTTON in Manual stop mode.
The samples stable method waits for the devices altitude not to change for the set number of samples. This is defined by not changing by more than +/- 1.0 meters for 98% of the samples, it's a reliable method to stop the recording after landing within 8-10 seconds (300 sample) or 16-20 seconds (600 sample).
The samples stable method waits for the devices altitude not to change for the set number of samples. This is defined by not changing by more than +/- 1.0 meters for 98% of the samples, it's a reliable method to stop the recording after landing within 8-10 seconds (300 sample) or 16-20 seconds (600 sample).
Auto: 450 samples stable (~9s)
Oversampling
i
Oversampling is a internal setting of the BMP 390 pressure sensor. It is how many samples are taken for each reading. By taking multiple samples for each pressure reading the altimeter reduces noise and increases the resolution of the output.
The sensor can run at 50 samples per second in 4X mode, so we suggest leaving it in this mode as it will offer the highest accuracy.
The sensor can run at 50 samples per second in 4X mode, so we suggest leaving it in this mode as it will offer the highest accuracy.
16x Oversampling
IIR filter
i
The IIR filter is another internal sensor for the BMP390 pressure sensor. It is a Infinite impulse response filter used to enhance pressure measurement accuracy by reducing noise. It's primarily for smoothing out rapid pressure changes.
We suggest not setting this too high as it will cause delay to changes in altitude if set very high.
We suggest not setting this too high as it will cause delay to changes in altitude if set very high.
COEFF 7
Pressure filter
i
This filter is a software Kalman filter that runs on the altimeters processor.
The Kalman filter uses a prediction step based on a system model and then a correction step using new measurements to refine its estimate, it creates accurate most certain results from data with noise in it.
The Kalman filter uses a prediction step based on a system model and then a correction step using new measurements to refine its estimate, it creates accurate most certain results from data with noise in it.
TruePath 1.0
Sample speed
i
The sample rate of the altimeter's sensors. 50Hz takes 50 samples per second, 100Hz takes 100 samples per second for higher resolution data.
100 Hz
Hybrid mode
i
When enabled, the altimeter records at full speed during ascent then switches to half speed after apogee to extend recording time during descent.
Enabled (1/3 rate after apogee)
Sync sensors
i
The filters on the pressure sensor can cause it to lag very slightly behind the Accelerometer and Gyroscope data.
The Sync sensors option detects how far out of sync these sensors are. It then corrects the Acceleration and Gyroscope readings to match the pressure sensor.
AKTIVOVÁNO (21 samples / 213ms)
Orientation
i
This is the orientation you intend to install the Altimeter in your rocket. It's needed to ensure completly accurate angles and orientation charts and reports. Check out the Manual for more information on this.
Down (text up)
IMU filter
i
The IMU filter, or fusion filter takes the data from each axis of the Gyroscope and Accelerometer to calculate the Pitch, Roll, Yaw and tilt angle from vertical.
These filters can build up some discrepency over time so it's important to calibrate your sensors to minimise this.
Madgwick 6-Axis
Launch ALP
i
This is prevention against accidental launch detection.
With this disabled the launch is based only on pressure and something that creates a low pressure can trigger the flight by accident. For example pulling your nose cone off can even trigger it.
With this enabled the rocket also needs to have seen 8 samples (0.25 seconds) of acceleration above this setting in the last 3 seconds as well as the pressure drop to trigger. There is a backup trigger of 1.05 seconds of altitude being above the launch detect setting too.
There are very few situations where this option would cause issues, so we suggest leaving it on.
With this disabled the launch is based only on pressure and something that creates a low pressure can trigger the flight by accident. For example pulling your nose cone off can even trigger it.
With this enabled the rocket also needs to have seen 8 samples (0.25 seconds) of acceleration above this setting in the last 3 seconds as well as the pressure drop to trigger. There is a backup trigger of 1.05 seconds of altitude being above the launch detect setting too.
There are very few situations where this option would cause issues, so we suggest leaving it on.
1.5G
Launch lock
i
When enabled, the altimeter locks out recording for a set period after power on to prevent false triggering during setup.
DISABLED
Static temperature
i
A fixed temperature value used for altitude calculation when the external temperature sensor is disabled or not connected.
15 °C
Kalibrace senzorú
Kalibrační offsety použité pro tento let.
Gyroskop
⚠ Gyroskop nebyl zkalibrován
X
0.000°
Y
0.000°
Z
0.000°
Akcelerometr
⚠ Akcelerometr nebyl zkalibrován
X
0.000 mG
Y
0.000 mG
Z
0.000 mG
Komentáře
Komentáře
Přihlásit se pro komentování.
Přihlásit se pro komentování.